Electric Fan Relay Kit Instructions

Electric Fan Relay Kit Instructions. Install the thermoswitch into the cylinder head or intake manifold fitting as available per your application. Do not use electrical tape to.

NEW Adjustable Electric Fan Controller Kit threadin Probe with Relay from www.ebay.com

Powerful 120 watt motor will keep your engine cool. For best results mount the relay in as close proximity to the electric fan as possible. Thermostatically controlled electric fan relay kit for best results mount the relay in as close proximity to the electric fan as possible.

Source: www.aliexpress.com

For smaller fans, both fans can be connected to a single relay as shown above, and the proper fuse should be installed to protect the circuit while at the same time providing enough current to flow without exceeding the fuse rating. Mount the relay under the hood in a convenient location as close to the fan as possible.

Source: www.ebay.com

This is based on the draw from the fans, if the fans are larger and draw more than 15 amps each, it's recommended to install a second relay kit as shown below. Make sure the area you mount this provides a clean ground for the black wire.

Source: www.ebay.com

This is the load side of the relay and you should use a minimum of 14 gauge wire here. The relay should be mounted in a secure location away from extreme heat or outside elements.

Source: ceautoelectricsupply.com

Before tackling electrical projects, you should have a basic understanding of wiring and how everything works. Lastly, connect a fused constant power to both of the red wires on the relays.

Source: www.ebay.com

Each kit comes with easy to follow instructions that are specifically for that application. Connect the red wire to the sending unit wire of the original fan relay harness.

Source: ceautoelectricsupply.com

Mount the relays under the hood in a convenient location as close to the fans as possible. The black wire with the ring terminal preinstalled will also need to be grounded with this terminal.

Source: www.ebay.com

These instructions will show you how to properly install the relay and harness for our performance cooling fans. Installation instructions for the universal thermostatically controlled electric fan relay kit.

Source: stores.lsxeverything.com

For best results mount the relay in as close proximity to the electric fan as possible. You may use this attachment for the grey ground

Source: cookinglove.com

Configured as an air puller out of the box. This fan control kit can be used with single fan or multiple fan applications as long and the combined current draw does not exceed 30 amps.

Source: www.ebay.com

This fan control kit can be used with single fan or multiple fan applications as long and the. Be sure to route wires in a manner so that they do not chafe on any sharp metal edges and use proper terminals and connectors at all connecting points to insure proper electric fan function.

Source: autoplicity.com

Connections to the vehicle should be done per the notes and diagrams. This fan control kit can be used with single fan or multiple fan applications as long and the.

Source: www.carid.com

Mount the relays under the hood in a convenient location as close to the fans as possible. Mount the thermoswitch into the cylinder head or intake manifold, so that the bottom of the switch is immersed in coolant.

You May Use This Attachment For The Grey Ground

Connections to the vehicle should be done per the notes and diagrams. Blade and wiring can be reversed to. Be sure to route wires in a manner so that they do not chafe on any sharp metal edges and use proper terminals and connectors at all connecting points to insure proper electric fan function.

Wire Crimp Terminals & Hardware

Secure the relay assembly with the included sheet metal screw. 16 inch reversible 12 volt electric cooling fan. This is based on the draw from the fans, if the fans are larger and draw more than 15 amps each, it's recommended to install a second relay kit as shown below.

Install Thermostat Into A Water Jacket In The Head.

Route the wires away from heat and sharp metal edges that may cause melting or damage to the wires. Home » tanpa label » electric fan wiring : The black wire with the ring terminal preinstalled will also need to be grounded with this terminal.

Mount The Thermoswitch Into The Cylinder Head Or Intake Manifold, So That The Bottom Of The Switch Is Immersed In Coolant.

Installation instructions for the universal thermostatically controlled electric fan relay kit. This fan harness & relay kit can be used with one or two electric fans as long as the total amperage draw does not exceed 30 amps. For smaller fans, both fans can be connected to a single relay as shown above, and the proper fuse should be installed to protect the circuit while at the same time providing enough current to flow without exceeding the fuse rating.

Universal Fit For Hot Rods, Classic Engines And Modern Vehicles.

Additional instructions are provided for those with fuel injected vehicles equipped with an ecm that has cooling fan activation capabilities. Next, both of the black wires from the relays are spliced together and connected to your thermostatic switch. Mount the relays under the hood in a convenient location as close to the fans as possible.